Home Products About us News Case FQA Download Contact us      
your position:homeproducts>orifice plate
Catalogue
Electromagnetic Flowmeter
Vortex Flowmeter
Turbine Flowmeter
Ultrasonic Flowmeter
Metal Tube Rotameter
Level Meter
Orifice plate

Stainless Steel Standard Orifice plate

Size2" to 40" (larger line size available on application)
pressure: 150# to 2500# (Higher Pressure Available On Application)
Restrictor Material:SS304, SS316, Monel, Inconel & Hastelloy (Other Material Available On Application)
Flange Standard:ANSI,ASME,JIS,JPI,DIN,GB,JB
Flange Material:Carbon steel, Stainless Steel, (Other Material Available On Application)
 
 

 

Overview Technical data Inquiry

Principle

 

The throttling device shall be assembled into the ring pipe,when the fluid flows through the throttling element,the differential-pressure will

appear between the upstream and downstream sides,See figure 1.

In accordance with Bernoullis equation,the flow basic equation can be obtained by derivation.

In the formula:

qm:-------The mass flow of the fluid kg/h


C:-------Output coefficient

ţ------The expandable coefficient of the beam of flow after the fluid flows?? through the throttling element.(to liquid =1

£------Radial ratio(=d/D,OF them d: bore diameter of the orifice,D: the inside diameter of the pipe)

P:----The dp value obtained from the pressure tap side at the downstream and upstream of the throttling element.kPa

:-----The density of the fluid.kg/m3

The dp value shall be turned into standard current signal with dp transmitter,further,by indicating meter or data processing device,the flow and total flow of the fluid shall be displayed.

 


Introduction

    • simple structure, convenient for assembly ,correct measurement, without actual flow calibration;
    • low manufacturing cost, flange tapping, diameral-distance tapping;
    • corner tapping, flange tapping ,diameral-distance tapping;
    • accuracy is proper,0.5%-1.5%
    • the accessory complete,the design and calculation can be done for the customer.
    • The plate handles are stamped with relevant information such as tag No.,Line I.D, bore size as an example.

    Technical parameters

    Assembly consists of

      • 2x flanges
      • Studs&Nuts
      • Gasket(if raised face type)
      • Orifice plate

      Application criteria

      • wide range flowing medium properties
      • medium for manifold
      • no maintenance requirements
      • space challenges
      • moderate measurement accuracy

      Line size:2 to 40(larger line size available on application)
      Pressure:150# to 2500#(Higher pressure available on application)
      Restrictor material:SS304,SS316,Monel,Inconel&Hastelloy(other material available on application)
      Flange standard :ANSI, ASME,JIS ,JPI,DIN,GB,JB
      Flange material: carbon steel ,stainless steel ,(other material available on application)
      Trim: carbon steel, stainless steel ,(other material available on application)
      Studs,Nuts: Carbon steel ,Stainless steel

      Differential pressure Tap type: Pipe,NPT, Flanged,Valve

 

 
 
 

Installation

Normally,the mode to connect the throttling device and the pipe line is welding,attention must be paid for this structure:First of all,two sections of nipples that are same as the processing pipe line shall be selected, the length shall be between 100-500mm,the end face of the nipples should be plane, they shall be firmly welded in butt welding to the two flanges associated withe the throttling device respectively,then, the throttling device with a section of nipple shall be welded in butt welding to the processing pipe line

Application

  • gas
  • liquid
  • stream

 

 

 

 

 

Project Case

 

 

 

 

 

 

 

Telephone:0086-18336316296

Email:mary.manager@kfkc-instrument.com,sales1_kfkc@126.com

Mobile Phone:0086-18336316296

Fax:0086-371-26669968

Address:3 Road, economic development area, Kaifeng City,Henan Province,China.

 

Copyright @ KFKC INSTRUMENT CO.,LTD